low noise oscillator series lno 100 ocxo lno 100 july 22nd, 2014 specifications subject to change witho ut notice shortform , 51001185.110 , issue a4 1 / 9 www.rakon .com specific request can be addressed to rakon info@rakon.fr product description this low noise oven controlled crystal oscillator available in diffe rent footprints from 38 x 38 x22 mm (1.5x1.5 x0.8 ) till 25x22 x12 mm (1 x0.8 x0.5) , is specifically designed to meet the request of the most demanding phase noise applications in the instrumentation and defence industries. the lno 100 @ 100 mhz can be provided with a guaranteed phase noise level of up to - 165 dbc/hz @ 1 k h z a nd a g - s ensitivity down to 0.5 ppb/ g . features ? low noise oscillator ( lno), oven controlled crystal oscillator (ocxo) ? frequency : 80 to 125 mhz ? guaranteed l ow phase noise @ 100 mhz : - 165 dbc/hz @ 1khz offset - 178 dbc/hz @ 10 0 khz offset ? supply voltage : + 12v & +15v ? pin through hole , smd package or with connectors ? frequency stability vs. temperature: 0.2 ppm ? ageing : 1.6 ppm over 10 years ? rohs compliant applications ? reference for phase noise measurement ? synthesizers ? test equipment ? radar ? military communication typical phase noise curve @ 100 mhz courtesy noise xt
low noise oscillator series lno 100 ocxo lno 100 july 22nd, 2014 specifications subject to change witho ut notice shortform , 51001185.110 , issue a4 2 / 9 www.rakon .com specifications 1. environmental conditions 2. electrical interface 3. performances parameters conditions/remarks min nom max unit option a 0 25 70 c option c -40 25 85 c switch-on temperature tso -40 85 c storage temperature -55 125 c sine vibration shock operating temperature level as per mil-prf-28800f, class 3, test equipment level as per mil-prf-28800f, class 3, test equipment parameters conditions/remarks min nom max unit option 12 11.40 12 12.60 v option 15 14.25 15 15.75 v load impedance 45 50 55 w input impedance 10 kw power supply parameters conditions/remarks min typ max unit nominal frequency 80 125 mhz relative pulling frequency range (positive slope) 1.8 ppm control voltage 0 10 v steady state input power typical @ 25c 2.2 w warm up input power nominal frequency is achieved 5mn after start up @ 25c 3.7 w initial frequency accuracy @ 25c 0.1 ppm option a (peak-peak) (0c70c) 0.2 ppm option c (-40c+85c) 0.5 ppm frequency variation vs. supply voltage vcc 5% @25c 0.02 ppm frequency variation vs. load for 10% variation of load 0.02 ppm 1st year 0.5 ppm 10 years 1.6 ppm tau=1s 5e-11 tau= 10s 5e-10 frequency warm up time to be within the init. freq. accuracy compared to freq. after 1h 5 mn option sg: on the worst axis 2 ppb/g option lg: on the worst axis (lower g-sensitivity can be provided) 0.5 ppb/g output waveform output level 11 13 15 dbm harmonics level -25 dbc spurious level -90 dbc modulation bandwidth 3 khz sine frequency stability vs temperature g-sensitivity frequency ageing after 30 days of continuous operation allan variance
low noise oscillator series lno 100 ocxo lno 100 july 22nd, 2014 specifications subject to change witho ut notice shortform , 51001185.110 , issue a4 3 / 9 www.rakon .com 4. minimum guaranteed phase noise level for performance levels at other frequencies, please consult your sales office. 5. mechanical features package name description dime nsions pth1 pin through hole 1.5x1.5x0.5 38x38x13 mm pth2 pin through hole europack 1.5x1x0.5 36x27 x13 mm pth3 pin through hole 1x1x0.5 25x25x13 mm pss1 pin side+sma 1.5 x 1.5 x0.8 38 x 38 x22 mm smd1 smd 1 x0.8 x0.5 25x22x12 mm frequency (mhz) performance level 100 hz 1 khz 10 khz 100 khz unit 80, 100, 120, 125 58 -130 -158 -172 -172 dbc/hz 80, 100, 120, 125 62 -130 -162 -175 -175 dbc/hz 100 65 -133 -165 -177 -178 dbc/hz
low noise oscillator series lno 100 ocxo lno 100 july 22nd, 2014 specifications subject to change witho ut notice shortform , 51001185.110 , issue a4 4 / 9 www.rakon .com 5.1. package pth1 (pin through hole) pin number name description 1 vcc supply voltage 2 gnd electrical & mechanical ground 3 gnd electrical & mechanical ground 4 fout frequency output 5 vc voltage control for electric al tun ing
low noise oscillator series lno 100 ocxo lno 100 july 22nd, 2014 specifications subject to change witho ut notice shortform , 51001185.110 , issue a4 5 / 9 www.rakon .com 5.2. package pth2 (pin through hole) pin number name description 1 fout frequency output 2 vcc supply voltage 3 n/c not connected 4 vc voltage control for electrical tuning 5 gnd electrical & mechanical ground
low noise oscillator series lno 100 ocxo lno 100 july 22nd, 2014 specifications subject to change witho ut notice shortform , 51001185.110 , issue a4 6 / 9 www.rakon .com 5.3. package pt h 3 (pin through hole ) pin number name description 1 fout frequency output 2 gnd electrical & mechanical ground 3 vc voltage control for electric al tuning 4 gnd electrical & mechanical ground 5 vcc supply voltage
low noise oscillator series lno 100 ocxo lno 100 july 22nd, 2014 specifications subject to change witho ut notice shortform , 51001185.110 , issue a4 7 / 9 www.rakon .com 5.4. package pss1 (pin side+sma) pin number name functio n 1 fout frequency output 2 vc voltage control for electrical tuning 3 vcc supply voltage 4 gnd electrical & mechanical ground
low noise oscillator series lno 100 ocxo lno 100 july 22nd, 2014 specifications subject to change witho ut notice shortform , 51001185.110 , issue a4 8 / 9 www.rakon .com 5.5. package smd1 (surface mount device) pin number name description 1 v c voltage control 2 n / c not connected 3 vcc supply voltage 4 fout frequency output 5 gnd electrical & mechanical ground
low noise oscillator series lno 100 ocxo lno 100 july 22nd, 2014 specifications subject to change witho ut notice shortform , 51001185.110 , issue a4 9 / 9 www.rakon .com 6. ordering part number definition the part number breakdown is defined as follows: standard frequencies: 80, 100, 120, 125mhz lnos with better ageing, be tter g - sensitivity can be provided. se ries package pth1 = 1.5x1.5x0.5 ( pin through hole ) pth2 = 1.5x1x0.5 ( pin through hole ) pth3 = 1x1x0.5 ( pin through hole ) pss1 = 1.5x1.5 x0.8 ( pin side + sma ) smd1 = 1x0.8 x0.5 ( smd ) supply voltage 12 = 12v 15 = 15v temperature ra nge/stability a = 0c to + 70c, 0.2 ppm (peak - peak ) c = - 40c to +85c, 0.5 ppm guaranted phase noise l evel 58 : - 1 58 dbc/hz @1khz , - 17 2 dbc/hz@10 0 khz 62 : - 1 62 dbc/hz@1khz, - 175 dbc/hz@10 0 khz 65 : - 1 65 dbc/hz@1khz, - 178 dbc/hz@10 0 khz LNO100 pth3 100m000000 frequency, fnom 65 a 1 2 g - sensitivity sg : 2 ppb/g lg : 0. 5 ppb/g lg
|
